cancel
Showing results for 
Search instead for 
Did you mean: 

Height glitching up and down

KevinLongtime
Level 7
Today I've been noticing this weird thing where I'm sitting inside of "I expect you to die" and while im sitting in my chair I get this glitch every once in a while where my height glitches upwards and I have to reset my default orientation to get it back down to normal. After a little while it will do it again. 

Anyone else have this?
199 REPLIES 199

Callidus80
Level 4
I have the same issue as well. I'm sure its only started since I got the second sensor. Here's a video showing the issue at its worst Also new video : https://youtu.be/CVElwsze650

Edit: Updated with Oculus_Log

KevinLongtime
Level 7


I have the same issue as well. I'm sure its only started since I got the second sensor. Here's a video showing the issue at its worst https://youtu.be/CVElwsze650


Hey, that looks awfully familiar! Mine wasn't doing it at that rate but perfect example of what it looks like. Thanks. Started with second sensor for me too, only really seem to be noticing it today though when I played something other than medium where im always standing. 

Updated OP with my logs

Callidus80
Level 4
I've updated my post with my most recent log also. I was loving all the new Touch gear but this has broken my whole experience. I'm reluctant start up any of the new games I've bought just have them ruined by this glitching. 😞

cybereality
Level 15
Thanks. We will investigate the issue.
AMD Ryzen 7 1800X | MSI X370 Titanium | G.Skill 16GB DDR4 3200 | EVGA SuperNOVA 1000 | Corsair Hydro H110i Gigabyte RX Vega 64 x2 | Samsung 960 Evo M.2 500GB | Seagate FireCuda SSHD 2TB | Phanteks ENTHOO EVOLV

kentbye
Level 2
I have also been experiencing this in most of the experiences I've been doing so far. It's pretty nauseating.

cybereality
Level 15
Please share your logs @kentbye. Thanks.
https://forums.oculus.com/community/discussion/33792/how-to-get-logs-for-bug-reports-for-consumer-ri...
AMD Ryzen 7 1800X | MSI X370 Titanium | G.Skill 16GB DDR4 3200 | EVGA SuperNOVA 1000 | Corsair Hydro H110i Gigabyte RX Vega 64 x2 | Samsung 960 Evo M.2 500GB | Seagate FireCuda SSHD 2TB | Phanteks ENTHOO EVOLV

Callidus80
Level 4
I'm not sure if it will assist but I have just spent the evening upgrading to a three sensor setup and I'm suffereing the same issue, so have attached new logs.

Also new video : https://youtu.be/DjWZ85XGlOw

elboffor
Level 12
i had something similar and it turned out it was because i adjusted one of the sensors after i had run the setup. i would recommend running the setup and making sure the sensors are kept in EXACTLY the same position. i literally adjusted one of mine by a few mil and and my screen was zooming in and out in the same manner yours is popping up and down.
This is my forum signature.
There are many others like it, but this is mine.

gamefan101
Level 5
Same issue here.  I used the DeskScene program and turned on the boundary lines to see what was happening. In the desk scene, you can also view from the camera position on the monitor.

It looks like the height of the sensor shifts, and perhaps because of this shift, the camera pitch and roll also changes slightly.  In my case, it stays at the new location until another shift happens a few seconds later. It's as tho the driver is trying to re-calibrate height, pitch and jaw somehow.

Seems to happen randomly, now and then.  I haven't found a position where I can consistently make it happen over and over.